Backtrack 5 Wireless problem

• 0Niko još nije pohvalio poruku.
  Registruj se da bi pohvalio/la poruku!

Upotrebio bih ga u edikativne svrhe,u pitanju je u stvari opklada koju ne zelim da izgubim

Pre,na ubuntu-u isto nije radio wireless ,ali se kroz update valjda instalirao i drajver ili sam ga mozda ja instalirao ,sada se ni ne secam,ali na ovome mislim da problem pravi bas drajver a ja ne znam kako da to proverim ili da ga instaliram.

Pokrecem ga preko fleske,live,kroz komande preko terminala sam zapazio da ne detektuje eth1 tj. wireless kartu ,u pitanju je laptop ,kartica inetrna Intel Corporation PRO/Wireless 2200BG
Mozda nesto od ovih informacija pomogne ,probao sam i apt-get update nije resilo problem

root@root:~# sudo iwconfig
lo        no wireless extensions.

eth0      no wireless extensions.

root@root:~# sudo lspci
00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller (rev 04)
00:02.0 VGA compatible controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 04)
00:02.1 Display controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 04)
00:1b.0 Audio device: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) High Definition Audio Controller (rev 04)
00:1c.0 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 (rev 04)
00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 04)
00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 04)
00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 04)
00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 04)
00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 04)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d4)
00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge (rev 04)
00:1f.1 IDE interface: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) IDE Controller (rev 04)
00:1f.2 SATA controller: Intel Corporation 82801FBM (ICH6M) SATA Controller (rev 04)
00:1f.3 SMBus: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus Controller (rev 04)
06:05.0 Network controller: Intel Corporation PRO/Wireless 2200BG [Calexico2] Network Connection (rev 05)
06:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169 Gigabit Ethernet (rev 10)
06:09.0 CardBus bridge: Texas Instruments PCIxx21/x515 Cardbus Controller
06:09.2 FireWire (IEEE 1394): Texas Instruments OHCI Compliant IEEE 1394 Host Controller
06:09.3 Mass storage controller: Texas Instruments PCIxx21 Integrated FlashMedia Controller
06:09.4 SD Host controller: Texas Instruments PCI6411/6421/6611/6621/7411/7421/7611/7621 Secure Digital Controller

root@root:~#  iwlist scan
lo        Interface doesn't support scanning.

eth0      Interface doesn't support scanning.


root@root:~# ifconfig
eth0      Link encap:Ethernet  HWaddr 00:0a:e4:b8:5c:0c 
          inet addr:192.168.1.100  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fe80::20a:e4ff:feb8:5c0c/64 Scope:Link
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:30113 errors:0 dropped:0 overruns:0 frame:0
          TX packets:23524 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:34464374 (34.4 MB)  TX bytes:2504264 (2.5 MB)
          Interrupt:20 Base address:0xc000

lo        Link encap:Local Loopback 
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:206 errors:0 dropped:0 overruns:0 frame:0
          TX packets:206 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:10801 (10.8 KB)  TX bytes:10801 (10.8 KB)



root@root:~# sudo lshw -C network
  *-network:0 UNCLAIMED 
       description: Network controller
       product: PRO/Wireless 2200BG [Calexico2] Network Connection
       vendor: Intel Corporation
       physical id: 5
       bus info: pci@0000:06:05.0
       version: 05
       width: 32 bits
       clock: 33MHz
       capabilities: pm cap_list
       configuration: latency=32 maxlatency=24 mingnt=3
       resources: memory:b8006000-b8006fff
  *-network:1
       description: Ethernet interface
       product: RTL-8169 Gigabit Ethernet
       vendor: Realtek Semiconductor Co., Ltd.
       physical id: 7
       bus info: pci@0000:06:07.0
       logical name: eth0
       version: 10
       serial: 00:0a:e4:b8:5c:0c
       size: 10MB/s
       capacity: 1GB/s
       width: 32 bits
       clock: 66MHz
       capabilities: pm bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation
       configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half ip=192.168.1.100 latency=64 link=no maxlatency=64 mingnt=32 multicast=yes port=MII speed=10MB/s
       resources: irq:20 ioport:3000(size=256) memory:b8007000-b80070ff memory:44000000-4401ffff

root@root:~# lsmod | grep ipw2200
ipw2200               140373  0
libipw                 42626  2 ipw2100,ipw2200
cfg80211              152934  3 ipw2100,ipw2200,libipw
lib80211                4418  2 ipw2200,libipw



imam mogucnost da ga povezem preko lan-a (adsl) na net

• 3Ovo se svidja korisnicima: TwinHeadedEagle, hazmaju, mcrule
  
  Registruj se da bi pohvalio/la poruku!

Kartica je uredno prepoznata, drajver učitan, ali najverovatnije nedostaje formware za nju. Njega je potrebno instalirati. Prvo ga preuzmi pomoću wget-a recimo:
wget http://http.us.debian.org/debian/pool/non-free/f/firmware-nonfree/firmware-ipw2x00_0.35_all.deb
Potom ga instaliraj
dpkg --install firmware-ipw2x00_0.35_all.deb
Nakon ovoga pomoću komandi koje si već koristio proveri da li adapter radi. Ako je sve u redu moraš naći način da napraviš stalnu promenu (da ne bi instalirao svaki put kada učitaš sistem).

• 0Niko još nije pohvalio poruku.
  Registruj se da bi pohvalio/la poruku!

hvala kolega na brzom odgovoru,bio je firmware,ali sam sada naisao na problem sa ukljucivanjem monitoring moda ,kao upali ali sa greskom i posle ocigledno ne radi kako treba


root@root:~# airmon-ng start eth1


Found 2 processes that could cause trouble.
If airodump-ng, aireplay-ng or airtun-ng stops working after
a short period of time, you may want to kill (some of) them!

PID   Name
2355   NetworkManager
2445   wpa_supplicant


Interface   Chipset      Driver

eth1      Intel 2200BG/2915ABG   ipw2200 - [phy0]mon0: ERROR while getting interface flags: No such device

            (monitor mode enabled on mon0)

root@root:~# iwconfig
lo        no wireless extensions.

eth0      no wireless extensions.

eth1      IEEE 802.11bg  ESSID:off/any 
          Mode:Managed  Channel:0  Access Point: Not-Associated   
          Bit Rate:0 kb/s   Tx-Power=20 dBm   Sensitivity=8/0 
          Retry limit:7   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:off
          Link Quality:0  Signal level:0  Noise level:0
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0


posle mi to pravi problem kod komande
root@root:~# airodump-ng mon0
Interface mon0:
ioctl(SIOCGIFINDEX) failed: No such device

ili programa Gerix wifi *****

Sto se tice toga da cu morati svaki put da instaliram ono,ne mora jer sam na fleshu ostavio storage prostor,pamti sve nakon restarta sistema

• 3Ovo se svidja korisnicima: mpman, hazmaju, mcrule
  
  Registruj se da bi pohvalio/la poruku!

Kucaj ovako komande

airmon-ng stop eth1
ifconfig eth1 down
airmon-ng start eth1
airodump-ng mon0

Zatim pici dalje...

• 0Niko još nije pohvalio poruku.
  Registruj se da bi pohvalio/la poruku!

ne zalost nece

root@root:~# airmon-ng stop eth1


Interface   Chipset      Driver

eth1      Intel 2200BG/2915ABG   ipw2200 - [phy0]
            (monitor mode disabled)

root@root:~# ifconfig eth1 down
root@root:~# airmon-ng start eth1


Found 2 processes that could cause trouble.
If airodump-ng, aireplay-ng or airtun-ng stops working after
a short period of time, you may want to kill (some of) them!

PID   Name
2393   NetworkManager
2476   wpa_supplicant

Interface   Chipset      Driver

eth1      Intel 2200BG/2915ABG   ipw2200 - [phy0]mon0: ERROR while getting interface flags: No such device

            (monitor mode enabled on mon0)

root@root:~# airodump-ng mon0
Interface mon0:
ioctl(SIOCGIFINDEX) failed: No such device



• 1Ovo se svidja korisniku: mcrule
  
  Registruj se da bi pohvalio/la poruku!

Cekaj, idemo postupno...

Prati sliku:

• 0Niko još nije pohvalio poruku.
  Registruj se da bi pohvalio/la poruku!

@TwinHeadedEagle

hvala sto si mi crtao,nisi morao,ali dobijam isto ono odozgo
posle komande airmon-ng start eth1 dobijam ovo,tako da airodump-ng mon0 posle ne prihvata

-----------------------
root@root:~# airmon-ng stop eth1
Found 2 processes that could cause trouble.
If airodump-ng, aireplay-ng or airtun-ng stops working after
a short period of time, you may want to kill (some of) them!

PID Name
2393 NetworkManager
2476 wpa_supplicant

Interface Chipset Driver

eth1 Intel 2200BG/2915ABG ipw2200 - [phy0]mon0: ERROR while getting interface flags: No such device

(monitor mode enabled on mon0)
-------------
root@root:~# airodump-ng mon0
Interface mon0:
ioctl(SIOCGIFINDEX) failed: No such device

--------------

nego ja sam skinuo verziju 2.30.2 da moozda probam ovo sa verzijom R2 ili nece nista znaciti

• 1Ovo se svidja korisniku: mcrule
  
  Registruj se da bi pohvalio/la poruku!

Kako sam ja pre nekog vremena procitao, nisam 100% siguran, ali mislim da ti je za Live resenja kao sto su USB ili DVD potreban adapter koji radi na USB prikljucak...
Predlazem ti da instaliras BT ili preko virtuelne masine ili na hard disk...

Kazem nisam 100% siguran, ja koristim BT 5 R1 na dvojku cu apdejtovati ovih dana...

Je si ti skinuo BT 5 R2 koja je najnovija verzija...

Jos jedna stvar koja moze da predstavlja problem jeste da tvoj adapter ne podrzava monitor mode, al mislin da su veliki broj adaptera podrzani u novim verzijama distribucije...

• 0Niko još nije pohvalio poruku.
  Registruj se da bi pohvalio/la poruku!

i ja sam juce trazeci resenje ovog problema naleteo na slicnu informaciju,iz FAQ a to je da kroz VM moze da radi samo usb wifi a na interni.
a probavao sam i preko virtual box-a ali nije radilo,probacu opet, samo sto tamo nisam update-ovao firmware koji je pravio problem.

probacu jos jednom na VM ,skinucu i R2 pa cu probati sa njim i live i u VM pa javljam sta sam uradio. Ne instalira mi se jer vec ima sedmica na laptopu i neki mali linux,Jolicloud mislim

ovo da ne podrzava monitor mode ,mislim da podrzava,mada nikad se ne zna,bicu bas te srece da ne podrzava

• 1Ovo se svidja korisniku: mcrule
  
  Registruj se da bi pohvalio/la poruku!

Instaliraj na VM mora da rafi 100%, ja ga imam odavno na VM, radi bez problema...

Ako negde zapne, tu sam