[RJESENO] Problem pri podizanju Ubuntu-a 9.04

• 0Niko još nije pohvalio poruku.
  Registruj se da bi pohvalio/la poruku!

naime sve je dosad ok radilo al od jucer mi pri bootovanju sistema izbacuje neke greske i to citanje gresaka traje jedno 2 minute i onda regularno podigne sistem i ucita sve i nema nikakvih problema
evo ss sta pise:

• 0Niko još nije pohvalio poruku.
  Registruj se da bi pohvalio/la poruku!

Jel se to dogadja posle update na zadnji kernel?
Daj nam ovde izlaz komande dmesg

• 0Niko još nije pohvalio poruku.
  Registruj se da bi pohvalio/la poruku!

Citat:[ 0.492001] PCI: Using configuration type 1 for base access
[ 0.493033] ACPI: EC: Look up EC in DSDT
[ 0.502356] ACPI: Interpreter enabled
[ 0.502364] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.502394] ACPI: Using PIC for interrupt routing
[ 0.517120] ACPI: No dock devices found.
[ 0.517135] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.517202] pci 0000:00:00.0: reg 10 32bit mmio: [0xe0000000-0xe7ffffff]
[ 0.517357] pci 0000:00:02.0: Enabling SiS 96x SMBus
[ 0.517409] pci 0000:00:02.1: reg 20 io port: [0xe600-0xe61f]
[ 0.517453] pci 0000:00:02.5: reg 10 io port: [0xd800-0xd807]
[ 0.517462] pci 0000:00:02.5: reg 14 io port: [0xd400-0xd403]
[ 0.517471] pci 0000:00:02.5: reg 18 io port: [0xd000-0xd007]
[ 0.517479] pci 0000:00:02.5: reg 1c io port: [0xb800-0xb803]
[ 0.517488] pci 0000:00:02.5: reg 20 io port: [0xb400-0xb40f]
[ 0.517547] pci 0000:00:02.7: reg 10 io port: [0xa400-0xa4ff]
[ 0.517557] pci 0000:00:02.7: reg 14 io port: [0xa000-0xa07f]
[ 0.517599] pci 0000:00:02.7: supports D1 D2
[ 0.517602] pci 0000:00:02.7: PME# supported from D3hot D3cold
[ 0.517607] pci 0000:00:02.7: PME# disabled
[ 0.517635] pci 0000:00:03.0: reg 10 32bit mmio: [0xde800000-0xde800fff]
[ 0.517698] pci 0000:00:03.1: reg 10 32bit mmio: [0xde000000-0xde000fff]
[ 0.517762] pci 0000:00:03.2: reg 10 32bit mmio: [0xdd800000-0xdd800fff]
[ 0.517838] pci 0000:00:03.3: reg 10 32bit mmio: [0xdd000000-0xdd000fff]
[ 0.517884] pci 0000:00:03.3: PME# supported from D0 D3hot D3cold
[ 0.517890] pci 0000:00:03.3: PME# disabled
[ 0.517937] pci 0000:00:04.0: reg 10 io port: [0x9800-0x98ff]
[ 0.517946] pci 0000:00:04.0: reg 14 32bit mmio: [0xdc800000-0xdc800fff]
[ 0.517980] pci 0000:00:04.0: reg 30 32bit mmio: [0xefee0000-0xefefffff]
[ 0.517993] pci 0000:00:04.0: supports D1 D2
[ 0.517995] pci 0000:00:04.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.518001] pci 0000:00:04.0: PME# disabled
[ 0.518068] pci 0000:00:10.0: reg 10 32bit mmio: [0xef000000-0xef000fff]
[ 0.518164] pci 0000:00:10.1: reg 10 32bit mmio: [0xee800000-0xee800fff]
[ 0.518265] pci 0000:00:13.0: reg 10 io port: [0x9400-0x943f]
[ 0.518314] pci 0000:00:13.0: supports D2
[ 0.518317] pci 0000:00:13.0: PME# supported from D0 D2 D3hot D3cold
[ 0.518323] pci 0000:00:13.0: PME# disabled
[ 0.518389] pci 0000:01:00.0: reg 10 32bit mmio: [0xdf000000-0xdfffffff]
[ 0.518397] pci 0000:01:00.0: reg 14 32bit mmio: [0xf0000000-0xf7ffffff]
[ 0.518422] pci 0000:01:00.0: reg 30 32bit mmio: [0xeffe0000-0xefffffff]
[ 0.518481] pci 0000:00:01.0: bridge 32bit mmio: [0xdf000000-0xdfffffff]
[ 0.518488] pci 0000:00:01.0: bridge 32bit mmio pref: [0xeff00000-0xfebfffff]
[ 0.518500] bus 00 -> node 0
[ 0.518507] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.519003] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
[ 0.599307] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 0.599436] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.599565] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.599693] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.599839] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *9
[ 0.599985] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *9
[ 0.600142] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *9
[ 0.600270] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.600420] ACPI: WMI: Mapper loaded
[ 0.600719] SCSI subsystem initialized
[ 0.600770] libata version 3.00 loaded.
[ 0.600843] usbcore: registered new interface driver usbfs
[ 0.600869] usbcore: registered new interface driver hub
[ 0.600905] usbcore: registered new device driver usb
[ 0.601066] PCI: Using ACPI for IRQ routing
[ 0.601194] Bluetooth: Core ver 2.13
[ 0.601194] NET: Registered protocol family 31
[ 0.601194] Bluetooth: HCI device and connection manager initialized
[ 0.601194] Bluetooth: HCI socket layer initialized
[ 0.601194] NET: Registered protocol family 8
[ 0.601194] NET: Registered protocol family 20
[ 0.601194] NetLabel: Initializing
[ 0.601194] NetLabel: domain hash size = 128
[ 0.601194] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.601194] NetLabel: unlabeled traffic allowed by default
[ 0.601194] AppArmor: AppArmor Filesystem Enabled
[ 0.601194] pnp: PnP ACPI init
[ 0.601194] ACPI: bus type pnp registered
[ 0.607910] pnp: PnP ACPI: found 17 devices
[ 0.607914] ACPI: ACPI bus type pnp unregistered
[ 0.607920] PnPBIOS: Disabled by ACPI PNP
[ 0.607933] system 00:00: iomem range 0x0-0x9ffff could not be reserved
[ 0.607937] system 00:00: iomem range 0xf0000-0xfffff could not be reserved
[ 0.607941] system 00:00: iomem range 0x100000-0x1fffffff could not be reserved
[ 0.607945] system 00:00: iomem range 0xfec00000-0xfec000ff has been reserved
[ 0.607948] system 00:00: iomem range 0xfee00000-0xfee00fff has been reserved
[ 0.607956] system 00:02: ioport range 0xe400-0xe47f has been reserved
[ 0.607960] system 00:02: ioport range 0xe480-0xe4ff has been reserved
[ 0.607963] system 00:02: ioport range 0xe600-0xe61f has been reserved
[ 0.607966] system 00:02: ioport range 0x480-0x48f has been reserved
[ 0.607970] system 00:02: iomem range 0xffee0000-0xffefffff has been reserved
[ 0.607977] system 00:03: iomem range 0xfffe0000-0xffffffff could not be reserved
[ 0.607985] system 00:04: ioport range 0x4d0-0x4d1 has been reserved
[ 0.608014] system 00:10: ioport range 0x3f0-0x3f1 has been reserved
[ 0.608017] system 00:10: ioport range 0x290-0x297 has been reserved
[ 0.642780] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[ 0.642784] pci 0000:00:01.0: IO window: disabled
[ 0.642791] pci 0000:00:01.0: MEM window: 0xdf000000-0xdfffffff
[ 0.642797] pci 0000:00:01.0: PREFETCH window: 0x000000eff00000-0x000000febfffff
[ 0.642816] pci 0000:00:01.0: setting latency timer to 64
[ 0.642822] bus: 00 index 0 io port: [0x00-0xffff]
[ 0.642824] bus: 00 index 1 mmio: [0x000000-0xffffffff]
[ 0.642827] bus: 01 index 0 mmio: [0x0-0x0]
[ 0.642830] bus: 01 index 1 mmio: [0xdf000000-0xdfffffff]
[ 0.642833] bus: 01 index 2 mmio: [0xeff00000-0xfebfffff]
[ 0.642835] bus: 01 index 3 mmio: [0x0-0x0]
[ 0.642848] NET: Registered protocol family 2
[ 0.643015] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.643320] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.643417] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.643506] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.643509] TCP reno registered
[ 0.643619] NET: Registered protocol family 1
[ 0.643795] checking if image is initramfs... it is
[ 1.144093] Switched to high resolution mode on CPU 0
[ 1.365056] Freeing initrd memory: 7373k freed
[ 1.365163] cpufreq: No nForce2 chipset.
[ 1.365393] audit: initializing netlink socket (disabled)
[ 1.365425] type=2000 audit(1242118758.364:1): initialized
[ 1.373439] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 1.374945] VFS: Disk quotas dquot_6.5.1
[ 1.375021] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.375844] fuse init (API version 7.10)
[ 1.375953] msgmni has been set to 994
[ 1.376225] alg: No test for stdrng (krng)
[ 1.376243] io scheduler noop registered
[ 1.376246] io scheduler anticipatory registered
[ 1.376249] io scheduler deadline registered
[ 1.376275] io scheduler cfq registered (default)
[ 1.424040] pci 0000:01:00.0: Boot video device
[ 1.430996] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 1.431011] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 1.431182] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[ 1.431185] ACPI: Power Button (FF) [PWRF]
[ 1.431241] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 1.431245] ACPI: Power Button (CM) [PWRB]
[ 1.431376] ACPI: Invalid PBLK length [5]
[ 1.431476] processor ACPI_CPU:00: registered as cooling_device0
[ 1.442043] isapnp: Scanning for PnP cards...
[ 1.795773] isapnp: No Plug & Play device found
[ 1.797367] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[ 1.797475] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.797581] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 1.798019] 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 1.798172] 00:0c: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 1.798309] serial 0000:00:13.0: enabling device (0080 -> 0081)
[ 1.798775] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
[ 1.798780] PCI: setting IRQ 11 as level-triggered
[ 1.798785] serial 0000:00:13.0: PCI INT A -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
[ 1.800183] brd: module loaded
[ 1.800629] loop: module loaded
[ 1.800750] Fixed MDIO Bus: probed
[ 1.800759] PPP generic driver version 2.4.2
[ 1.800847] input: Macintosh mouse button emulation as /devices/virtual/input/input2
[ 1.800893] Driver 'sd' needs updating - please use bus_type methods
[ 1.800908] Driver 'sr' needs updating - please use bus_type methods
[ 1.801682] pata_sis 0000:00:02.5: version 0.5.2
[ 1.802158] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
[ 1.802164] pata_sis 0000:00:02.5: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
[ 1.802411] scsi0 : pata_sis
[ 1.802552] scsi1 : pata_sis
[ 1.803347] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xb400 irq 14
[ 1.803351] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xb408 irq 15
[ 1.972511] ata1.00: ATA-6: ExcelStor Technology J680, V32OA60A, max UDMA/100
[ 1.972515] ata1.00: 160836480 sectors, multi 16: LBA48
[ 1.996541] ata1.00: configured for UDMA/100
[ 2.160298] ata2.00: ATAPI: ASUS DRW-1608P3S, 1.06, max UDMA/66
[ 2.160343] ata2.01: ATAPI: ASUS DVD-ROM E616, 2.2, max UDMA/100
[ 2.176324] ata2.00: configured for UDMA/66
[ 2.176804] ata2.01: configured for UDMA/100
[ 2.183829] scsi 0:0:0:0: Direct-Access ATA ExcelStor Techno V32O PQ: 0 ANSI: 5
[ 2.183967] sd 0:0:0:0: [sda] 160836480 512-byte hardware sectors: (82.3 GB/76.6 GiB)
[ 2.183990] sd 0:0:0:0: [sda] Write Protect is off
[ 2.183993] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.184037] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.184132] sd 0:0:0:0: [sda] 160836480 512-byte hardware sectors: (82.3 GB/76.6 GiB)
[ 2.184151] sd 0:0:0:0: [sda] Write Protect is off
[ 2.184154] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.184187] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.184192] sda: sda1 sda2 < sda5 sda6 >
[ 2.215901] sd 0:0:0:0: [sda] Attached SCSI disk
[ 2.215980] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 2.221988] scsi 1:0:0:0: CD-ROM ASUS DRW-1608P3S 1.06 PQ: 0 ANSI: 5
[ 2.240268] sr0: scsi3-mmc drive: 40x/40x writer dvd-ram cd/rw xa/form2 cdda tray
[ 2.240273] Uniform CD-ROM driver Revision: 3.20
[ 2.240414] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 2.240477] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 2.240746] scsi 1:0:1:0: CD-ROM ASUS DVD-ROM E616 2.2 PQ: 0 ANSI: 5
[ 32.816044] ata2.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 32.816107] ata2.01: cmd a0/01:00:00:80:00/00:00:00:00:00/b0 tag 0 dma 16512 in
[ 32.816109] cdb 5a 00 2a 00 00 00 00 00 80 00 00 00 00 00 00 00
[ 32.816110] res 40/00:03:00:00:00/00:00:00:00:00/b0 Emask 0x4 (timeout)
[ 32.816259] ata2.01: status: { DRDY }
[ 37.856017] ata2: link is slow to respond, please be patient (ready=0)
[ 42.840016] ata2: device not ready (errno=-16), forcing hardreset
[ 42.840024] ata2: soft resetting link
[ 43.020324] ata2.00: configured for UDMA/66
[ 43.020804] ata2.01: configured for UDMA/100
[ 43.026884] ata2: EH complete
[ 73.816042] ata2.01: limiting speed to UDMA/66:PIO4
[ 73.816047] ata2.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 73.816104] ata2.01: cmd a0/01:00:00:80:00/00:00:00:00:00/b0 tag 0 dma 16512 in
[ 73.816106] cdb 5a 00 2a 00 00 00 00 00 80 00 00 00 00 00 00 00
[ 73.816107] res 40/00:03:00:00:00/00:00:00:00:00/b0 Emask 0x4 (timeout)
[ 73.816255] ata2.01: status: { DRDY }
[ 78.856016] ata2: link is slow to respond, please be patient (ready=0)
[ 83.840016] ata2: device not ready (errno=-16), forcing hardreset
[ 83.840023] ata2: soft resetting link
[ 84.020323] ata2.00: configured for UDMA/66
[ 84.020815] ata2.01: configured for UDMA/66
[ 84.027558] ata2: EH complete
[ 114.816041] ata2.01: limiting speed to UDMA/33:PIO4
[ 114.816045] ata2.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 114.816102] ata2.01: cmd a0/01:00:00:80:00/00:00:00:00:00/b0 tag 0 dma 16512 in
[ 114.816104] cdb 5a 00 2a 00 00 00 00 00 80 00 00 00 00 00 00 00
[ 114.816105] res 40/00:03:00:00:00/00:00:00:00:00/b0 Emask 0x4 (timeout)
[ 114.816253] ata2.01: status: { DRDY }
[ 119.856014] ata2: link is slow to respond, please be patient (ready=0)
[ 124.840016] ata2: device not ready (errno=-16), forcing hardreset
[ 124.840023] ata2: soft resetting link
[ 125.020390] ata2.00: configured for UDMA/66
[ 125.020880] ata2.01: configured for UDMA/33
[ 125.027021] ata2: EH complete
[ 155.816041] ata2.01: limiting speed to PIO4
[ 155.816045] ata2.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 155.816114] ata2.01: cmd a0/01:00:00:80:00/00:00:00:00:00/b0 tag 0 dma 16512 in
[ 155.816116] cdb 5a 00 2a 00 00 00 00 00 80 00 00 00 00 00 00 00
[ 155.816117] res 40/00:03:00:00:00/00:00:00:00:00/b0 Emask 0x4 (timeout)
[ 155.816327] ata2.01: status: { DRDY }
[ 160.856014] ata2: link is slow to respond, please be patient (ready=0)
[ 165.840016] ata2: device not ready (errno=-16), forcing hardreset
[ 165.840023] ata2: soft resetting link
[ 166.020324] ata2.00: configured for UDMA/66
[ 166.020814] ata2.01: configured for PIO4
[ 166.027299] ata2: EH complete
[ 166.027310] sr1: scsi-1 drive
[ 166.027427] sr 1:0:1:0: Attached scsi CD-ROM sr1
[ 166.027495] sr 1:0:1:0: Attached scsi generic sg2 type 5
[ 166.027676] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 166.027707] ehci_hcd 0000:00:03.3: enabling device (0004 -> 0006)
[ 166.028198] ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
[ 166.028204] ehci_hcd 0000:00:03.3: PCI INT D -> Link[LNKH] -> GSI 11 (level, low) -> IRQ 11
[ 166.028238] ehci_hcd 0000:00:03.3: EHCI Host Controller
[ 166.028330] ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 1
[ 166.028382] ehci_hcd 0000:00:03.3: cache line size of 128 is not supported
[ 166.028393] ehci_hcd 0000:00:03.3: irq 11, io mem 0xdd000000
[ 166.040017] ehci_hcd 0000:00:03.3: USB 2.0 started, EHCI 1.00
[ 166.040114] usb usb1: configuration #1 chosen from 1 choice
[ 166.040151] hub 1-0:1.0: USB hub found
[ 166.040164] hub 1-0:1.0: 6 ports detected
[ 166.040306] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 166.040759] ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 10
[ 166.040763] PCI: setting IRQ 10 as level-triggered
[ 166.040768] ohci_hcd 0000:00:03.0: PCI INT A -> Link[LNKE] -> GSI 10 (level, low) -> IRQ 10
[ 166.040788] ohci_hcd 0000:00:03.0: OHCI Host Controller
[ 166.040851] ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2
[ 166.040871] ohci_hcd 0000:00:03.0: irq 10, io mem 0xde800000
[ 166.098092] usb usb2: configuration #1 chosen from 1 choice
[ 166.098126] hub 2-0:1.0: USB hub found
[ 166.098140] hub 2-0:1.0: 2 ports detected
[ 166.098669] ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 11
[ 166.098674] ohci_hcd 0000:00:03.1: PCI INT B -> Link[LNKF] -> GSI 11 (level, low) -> IRQ 11
[ 166.098690] ohci_hcd 0000:00:03.1: OHCI Host Controller
[ 166.098751] ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 3
[ 166.098769] ohci_hcd 0000:00:03.1: irq 11, io mem 0xde000000
[ 166.154071] usb usb3: configuration #1 chosen from 1 choice
[ 166.154106] hub 3-0:1.0: USB hub found
[ 166.154119] hub 3-0:1.0: 2 ports detected
[ 166.154650] ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 10
[ 166.154655] ohci_hcd 0000:00:03.2: PCI INT C -> Link[LNKG] -> GSI 10 (level, low) -> IRQ 10
[ 166.154672] ohci_hcd 0000:00:03.2: OHCI Host Controller
[ 166.154749] ohci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 4
[ 166.154766] ohci_hcd 0000:00:03.2: irq 10, io mem 0xdd800000
[ 166.210067] usb usb4: configuration #1 chosen from 1 choice
[ 166.210100] hub 4-0:1.0: USB hub found
[ 166.210115] hub 4-0:1.0: 2 ports detected
[ 166.210230] uhci_hcd: USB Universal Host Controller Interface driver
[ 166.210343] usbcore: registered new interface driver libusual
[ 166.210392] usbcore: registered new interface driver usbserial
[ 166.210408] USB Serial support registered for generic
[ 166.210428] usbcore: registered new interface driver usbserial_generic
[ 166.210431] usbserial: USB Serial Driver core
[ 166.210509] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 166.210795] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 166.210806] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 166.210967] mice: PS/2 mouse device common for all mice
[ 166.211136] rtc_cmos 00:06: RTC can wake from S4
[ 166.211183] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[ 166.211206] rtc0: alarms up to one month, 242 bytes nvram
[ 166.211294] device-mapper: uevent: version 1.0.3
[ 166.211462] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
[ 166.211527] device-mapper: multipath: version 1.0.5 loaded
[ 166.211531] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 166.211639] EISA: Probing bus 0 at eisa.0
[ 166.211678] EISA: Detected 0 cards.
[ 166.211718] cpuidle: using governor ladder
[ 166.211721] cpuidle: using governor menu
[ 166.212370] TCP cubic registered
[ 166.212467] NET: Registered protocol family 10
[ 166.212977] lo: Disabled Privacy Extensions
[ 166.213358] NET: Registered protocol family 17
[ 166.213384] Bluetooth: L2CAP ver 2.11
[ 166.213387] Bluetooth: L2CAP socket layer initialized
[ 166.213391] Bluetooth: SCO (Voice Link) ver 0.6
[ 166.213394] Bluetooth: SCO socket layer initialized
[ 166.213440] Bluetooth: RFCOMM socket layer initialized
[ 166.213454] Bluetooth: RFCOMM TTY layer initialized
[ 166.213456] Bluetooth: RFCOMM ver 1.10
[ 166.213525] IO APIC resources could be not be allocated.
[ 166.213592] Using IPI No-Shortcut mode
[ 166.213726] registered taskstats version 1
[ 166.213857] Magic number: 9:184:978
[ 166.213963] rtc_cmos 00:06: setting system clock to 2009-05-12 09:02:04 UTC (1242118924)
[ 166.213967] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 166.213969] EDD information not available.
[ 166.214579] Freeing unused kernel memory: 532k freed
[ 166.214712] Write protecting the kernel text: 4128k
[ 166.214758] Write protecting the kernel read-only data: 1532k
[ 166.250028] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[ 166.356079] usb 1-1: new high speed USB device using ehci_hcd and address 2
[ 166.494792] usb 1-1: configuration #1 chosen from 1 choice
[ 166.524082] Initializing USB Mass Storage driver...
[ 166.540145] scsi2 : SCSI emulation for USB Mass Storage devices
[ 166.552132] usbcore: registered new interface driver usb-storage
[ 166.552139] USB Mass Storage support registered.
[ 166.552297] usb-storage: device found at 2
[ 166.552300] usb-storage: waiting for device to settle before scanning
[ 166.676955] Floppy drive(s): fd0 is 1.44M
[ 166.695879] FDC 0 is a post-1991 82077
[ 166.811128] sis900.c: v1.08.10 Apr. 2 2006
[ 166.811195] sis900 0000:00:04.0: enabling device (0004 -> 0007)
[ 166.832678] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
[ 166.832687] sis900 0000:00:04.0: PCI INT A -> Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
[ 166.834196] 0000:00:04.0: Realtek RTL8201 PHY transceiver found at address 1.
[ 166.846585] 0000:00:04.0: Using transceiver found at address 1 as default
[ 166.879348] eth0: SiS 900 PCI Fast Ethernet at 0x9800, IRQ 11, 00:0c:6e:97:b3:0c
[ 167.546451] PM: Starting manual resume from disk
[ 167.546456] PM: Resume from partition 8:6
[ 167.546459] PM: Checking hibernation image.
[ 167.546677] PM: Resume from disk failed.
[ 167.550311] EXT3-fs: INFO: recovery required on readonly filesystem.
[ 167.550316] EXT3-fs: write access will be enabled during recovery.
[ 168.267782] kjournald starting. Commit interval 5 seconds
[ 168.267811] EXT3-fs: sda1: orphan cleanup on readonly fs
[ 168.267819] ext3_orphan_cleanup: deleting unreferenced inode 1545267
[ 168.267873] ext3_orphan_cleanup: deleting unreferenced inode 1578027
[ 168.267882] EXT3-fs: sda1: 2 orphan inodes deleted
[ 168.267884] EXT3-fs: recovery complete.
[ 168.276434] EXT3-fs: mounted filesystem with ordered data mode.
[ 171.552326] usb-storage: device scan complete
[ 171.552914] scsi 2:0:0:0: Direct-Access KINGSTON DataTraveler 2.0 1.00 PQ: 0 ANSI: 2
[ 171.553893] sd 2:0:0:0: [sdb] 3902464 512-byte hardware sectors: (1.99 GB/1.86 GiB)
[ 171.554514] sd 2:0:0:0: [sdb] Write Protect is off
[ 171.554518] sd 2:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 171.554521] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 171.556143] sd 2:0:0:0: [sdb] 3902464 512-byte hardware sectors: (1.99 GB/1.86 GiB)
[ 171.556764] sd 2:0:0:0: [sdb] Write Protect is off
[ 171.556768] sd 2:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 171.556770] sd 2:0:0:0: [sdb] Assuming drive cache: write through
[ 171.556775] sdb: sdb1
[ 171.557673] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 171.557763] sd 2:0:0:0: Attached scsi generic sg3 type 0
[ 173.719860] udev: starting version 141
[ 174.427724] parport_pc 00:0a: reported by Plug and Play ACPI
[ 174.427782] parport0: PC-style at 0x378 (0x778-), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[ 174.758015] input: PC Speaker as /devices/platform/pcspkr/input/input4
[ 174.784599] sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0xe600
[ 174.829104] Linux agpgart interface v0.103
[ 174.842925] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 174.928135] ppdev: user-space parallel port driver
[ 175.063524] nvidia: module license 'NVIDIA' taints kernel.
[ 175.325537] nvidia 0000:01:00.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
[ 175.326221] NVRM: loading NVIDIA Linux x86 Kernel Module 96.43.10 Sat Jan 24 19:49:38 PST 2009
[ 175.370519] agpgart-sis 0000:00:00.0: SiS chipset [1039/0645]
[ 175.380700] agpgart-sis 0000:00:00.0: AGP aperture is 128M @ 0xe0000000
[ 175.427518] synaptics was reset on resume, see synaptics_resume_reset if you have trouble on resume
[ 175.434634] Linux video capture interface: v2.00
[ 175.492600] bttv: driver version 0.9.17 loaded
[ 175.492605] bttv: using 8 buffers with 2080k (520 pages) each for capture
[ 175.494182] bttv: Bt8xx card found (0).
[ 175.494203] bttv 0000:00:10.0: enabling device (0004 -> 0006)
[ 175.494219] bttv 0000:00:10.0: PCI INT A -> Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
[ 175.494235] bttv0: Bt878 (rev 17) at 0000:00:10.0, irq: 11, latency: 32, mmio: 0xef000000
[ 175.494300] bttv0: detected: Pinnacle PCTV Sat [card=94], PCI subsystem ID is 11bd:001c
[ 175.494304] bttv0: using: Pinnacle PCTV Sat [card=94,autodetected]
[ 175.494347] bttv0: gpio: en=00000000, out=00000000 in=009f00fc [init]
[ 175.494435] bttv0: tuner absent
[ 175.494824] bttv0: registered device video0
[ 175.502788] bttv0: registered device vbi0
[ 175.502815] bttv0: PLL: 28636363 => 35468950 .. ok
[ 175.532104] bttv0: add subdevice "dvb0"
[ 175.581363] bt878: AUDIO driver version 0.0.0 loaded
[ 175.581661] bt878: Bt878 AUDIO function found (0).
[ 175.581714] bt878 0000:00:10.1: enabling device (0004 -> 0006)
[ 175.581796] bt878 0000:00:10.1: PCI INT A -> Link[LNKD] -> GSI 11 (level, low) -> IRQ 11
[ 175.581801] bt878_probe: card id=[0x1c11bd],[ Pinnacle PCTV Sat ] has DVB functions.
[ 175.581811] bt878(0): Bt878 (rev 17) at 00:10.1, irq: 11, latency: 32, memory: 0xee800000
[ 175.599048] DVB: registering new adapter (bttv0)
[ 175.645850] DVB: registering adapter 0 frontend 2550822 (Conexant CX24110 DVB-S)...
[ 175.759473] Intel ICH 0000:00:02.7: enabling device (0004 -> 0005)
[ 175.759488] Intel ICH 0000:00:02.7: PCI INT C -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11
[ 175.921016] psmouse serio1: ID: 10 00 64<6>intel8x0_measure_ac97_clock: measured 52319 usecs
[ 176.180015] intel8x0: clocking to 48000
[ 176.357056] lp0: using parport0 (interrupt-driven).
[ 176.484373] input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/serio1/input/input5
[ 176.513014] Adding 594364k swap on /dev/sda6. Priority:-1 extents:1 across:594364k
[ 176.873013] usb 3-1: new full speed USB device using ohci_hcd and address 2
[ 177.079941] EXT3 FS on sda1, internal journal
[ 177.227662] usb 3-1: configuration #1 chosen from 1 choice
[ 177.298134] Bluetooth: Generic Bluetooth USB driver ver 0.3
[ 177.298236] usbcore: registered new interface driver btusb
[ 178.330487] type=1505 audit(1242118936.614:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=1994
[ 178.394024] type=1505 audit(1242118936.678:3): operation="profile_load" name="/sbin/dhclient-script" name2="default" pid=1998
[ 178.394318] type=1505 audit(1242118936.678:4): operation="profile_load" name="/sbin/dhclient3" name2="default" pid=1998
[ 178.394395] type=1505 audit(1242118936.678:5): operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" name2="default" pid=1998
[ 178.394465] type=1505 audit(1242118936.678:6): operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" name2="default" pid=1998
[ 178.438411] type=1505 audit(1242118936.722:7): operation="profile_load" name="/usr/bin/freshclam" name2="default" pid=2003
[ 178.617831] type=1505 audit(1242118936.902:: operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=2007
[ 178.618214] type=1505 audit(1242118936.902:9): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=2007
[ 178.658270] type=1505 audit(1242118936.942:10): operation="profile_load" name="/usr/sbin/tcpdump" name2="default" pid=2011
[ 178.817671] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 178.846676] nf_conntrack version 0.5.0 (8191 buckets, 32764 max)
[ 178.846919] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
[ 178.846923] nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or
[ 178.846925] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[ 178.922815] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 190.769334] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 190.769339] Bluetooth: BNEP filters: protocol multicast
[ 190.801036] Bridge firewalling registered
[ 192.981783] agpgart-sis 0000:00:00.0: AGP 2.0 bridge
[ 192.981808] agpgart-sis 0000:00:00.0: putting AGP V2 device into 4x mode
[ 192.981879] nvidia 0000:01:00.0: putting AGP V2 device into 4x mode
[ 197.717217] eth0: Media Link On 100mbps full-duplex
[ 205.792027] eth0: no IPv6 routers present
[ 547.151522] usb 3-1: USB disconnect, address 2
[ 547.152329] btusb_bulk_complete: hci0 urb defc0180 failed to resubmit (19)
[ 547.152340] btusb_intr_complete: hci0 urb defc0100 failed to resubmit (19)
[ 547.153325] btusb_bulk_complete: hci0 urb defc0700 failed to resubmit (19)
[ 547.155679] btusb_send_frame: hci0 urb de65e980 submission failed
[ 559.055704] NET: Registered protocol family 24


ne znam sta je u pitanju...a i nisam neki veliki poznavaoc linuxa al mi je bas sve radilo ok..sistem je updateovan redovno...

• 0Niko još nije pohvalio poruku.
  Registruj se da bi pohvalio/la poruku!

Mislim da nnisi iskopirao ceo output komande. Uradi ovu komandu dmesg > dmesg.txt pa uploaduj fajl iz home/user direktorijuma na forum.

Imas li i Win i kako ti se on dize?
Slabo kapiram ovaj tvoj problem, medjutim sumnjam na neki problem sa odzivom hard diska. Kako bi bilo da odes u BIOS i da tamo malo redetektujes hard i stavis PIO 4 ili Auto, a probaj i da resetujes sva podesenja u BIOSu na default (cesto F5). Pa javi, ima li nekog poboljsanja.

Javice se jos neko pametniji, pa mozda bude imao tacniju predstavu gde je problem.

• 0Niko još nije pohvalio poruku.
  Registruj se da bi pohvalio/la poruku!

Uloguj se preko Facebooka da bi skinuo fajl:

Napisano: 12 Maj 2009 13:14

evo fajla

https://www.mycity.rs/must-login.png

a nemam Windows na kompjuteru...
i ja mislim da je nesto sa hard diskom u pitanju...
probacu ovo u bios-u da vidim ova podesavanja sto si mi predlozio
eto ako ima jos neko neki prijedlog...

Dopuna: 12 Maj 2009 13:37

hazmaju ::Kako bi bilo da odes u BIOS i da tamo malo redetektujes hard i stavis PIO 4 ili Auto, a probaj i da resetujes sva podesenja u BIOSu na default (cesto F5). Pa javi, ima li nekog poboljsanja.

HDD je bio na auto i PIO na 4...resetovao sam sva podesavanja BIOS-a i opet isto...

• 0Niko još nije pohvalio poruku.
  Registruj se da bi pohvalio/la poruku!

Skini program GSmartControl odavde 554kb i instaliraj. U njemu ces naci kompletnu dijagnostiku harda i svih njegovih komponenti. Ima nekih testova koje mozes da uradis, ne pitaj me kako se upotrebljava, provalices, malo se pozabavi sa njim.
Pogledaj i ovu temu http://www.mycity.rs/Windows/Problem-sa-racunarom-4.html

• 0Niko još nije pohvalio poruku.
  Registruj se da bi pohvalio/la poruku!

hazmaju ::Skini program GSmartControl odavde 554kb i instaliraj. U njemu ces naci kompletnu dijagnostiku harda i svih njegovih komponenti. Ima nekih testova koje mozes da uradis, ne pitaj me kako se upotrebljava, provalices, malo se pozabavi sa njim.

Instalirao sam ovaj GSmart i uradio Extend Self Test tamo pod karticom Perform test
i nije mi nasao nikakvu gresku (test Result: Completed without error)
medjutim pod karticom Error Log mi pise ovo:
Citat:smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===
Device Model: ExcelStor Technology J680
Serial Number: VNR21EG20099BA
Firmware Version: V32OA60A
User Capacity: 82,348,277,760 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 6
ATA Standard is: ATA/ATAPI-6 T13 1410D revision 3a
Local Time is: Tue May 12 15:07:00 2009 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (1828-) seconds.
Offline data collection
capabilities: (0x1b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 31) minutes.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 060 Pre-fail Always - 0
2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0
3 Spin_Up_Time 0x0007 136 136 024 Pre-fail Always - 154 (Average 140)
4 Start_Stop_Count 0x0012 099 099 000 Old_age Always - 7936
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 4
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 020 Pre-fail Offline - 0
9 Power_On_Hours 0x0012 099 099 000 Old_age Always - 13178
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 7377
192 Power-Off_Retract_Count 0x0032 094 094 050 Old_age Always - 7958
193 Load_Cycle_Count 0x0012 094 094 050 Old_age Always - 7958
194 Temperature_Celsius 0x0002 122 122 000 Old_age Always - 45 (Lifetime Min/Max 7/55)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 4
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0

SMART Error Log Version: 1
ATA Error Count: 1
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 1 occurred at disk power-on lifetime: 6778 hours (282 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 7f d0 8a 60 e0 Error: UNC 127 sectors at LBA = 0x00608ad0 = 6326992

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 d8 80 cf 8a 60 e0 00 00:00:46.500 READ DMA
c8 d8 68 d7 87 60 e0 00 00:00:46.400 READ DMA
c8 d8 00 27 84 60 e0 00 00:00:46.400 READ DMA
c8 d8 00 27 83 60 e0 00 00:00:46.400 READ DMA
c8 d8 18 07 81 60 e0 00 00:00:46.400 READ DMA

SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 13178 -

Device does not support Selective Self Tests/Logging

• 0Niko još nije pohvalio poruku.
  Registruj se da bi pohvalio/la poruku!

da li si dodao skoro ovaj uređaj ? dvd-rom asus E616
(izgleda na njemu javlja nešto)

Citat:
[ 2.160343] ata2.01: ATAPI: ASUS DVD-ROM E616, 2.2, max UDMA/100

[ 2.176804] ata2.01: configured for UDMA/100

[ 2.240746] scsi 1:0:1:0: CD-ROM ASUS DVD-ROM E616 2.2 PQ: 0 ANSI: 5
[ 32.816044] ata2.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 32.816107] ata2.01: cmd a0/01:00:00:80:00/00:00:00:00:00/b0 tag 0 dma 16512 in
[ 32.816109] cdb 5a 00 2a 00 00 00 00 00 80 00 00 00 00 00 00 00
[ 32.816110] res 40/00:03:00:00:00/00:00:00:00:00/b0 Emask 0x4 (timeout)
[ 32.816259] ata2.01: status: { DRDY }

[ 43.020324] ata2.00: configured for UDMA/66
[ 43.020804] ata2.01: configured for UDMA/100

[ 73.816042] ata2.01: limiting speed to UDMA/66:PIO4
[ 73.816047] ata2.01: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 73.816104] ata2.01: cmd a0/01:00:00:80:00/00:00:00:00:00/b0 tag 0 dma 16512 in
[ 73.816106] cdb 5a 00 2a 00 00 00 00 00 80 00 00 00 00 00 00 00
[ 73.816107] res 40/00:03:00:00:00/00:00:00:00:00/b0 Emask 0x4 (timeout)
[ 73.816255] ata2.01: status: { DRDY }

mislim da ne mogu oba sa ovim drajverom libata da idu jedan na dma 66 a drugi na dma 100,pa ih onda stavi na isti - dma 66 ? ili se posle ažuriranja kernela to javilo
(ako je ranije išlo ok)

sa glavnim diskom ,izgleda da je u redu ,ovo što javlja se odnosi na cd-uređaje

nema potrebe za MHDD iz druge teme , mislim da nema potrebe i za
daljim pregledom SMART parametara ,pomoću GSmartControl
onaj prvi je potencijalno opasan program, dok za smart takođe ako se
previše testira sa ovim testovima,i ako je stariji hard disk ,može da otkaže eventualno (sa onim dužim self testom)

samrt parametri izgledaju u redu ,na prvi pogled
(oni su samo za hard diskove ,ne i za dvd/cd uređaje)

• 0Niko još nije pohvalio poruku.
  Registruj se da bi pohvalio/la poruku!

prvo je bio ubuntu 8.10 i nije bilo nikakvih problema
poslije sam instalirao 9.04 (nanovo instalirao i nije bilo nikakve greske)
imam u kompjuteru DVD ROM (taj Asus E616) koji je star kao grcka i jos jedan Asusov DVD RW koji je noviji. (oba su tu jos i pri instalaciji 8.10)

mogu li da probam da iskljucim taj DVD ROM i da probam da li ce se greske javljati ili imas neki pametniji prijedlog?

• 0Niko još nije pohvalio poruku.
  Registruj se da bi pohvalio/la poruku!

ok probaj da otkašiš DVD -rom asus

druga ideja bi bila da se stavi taj dvd rom kao master a rezač da bude slava

treća ideja je da se doda kernel boot parametar
koji forsira da se taj uređaj odmah stavi u dma 66
(nisam siguran trenutno kako ide to, mora da se pogleda u dokumentaciji)

menjanje parametara u biosu ne pomaže kod novih linux-ova jer
libata drajver ide sa detekcijom nezavisno od biosa

EDIT: četvrta mogućnost je da ostaneš na ubuntu 8.10 ?